最近JN0-522試験は本当にもてますね、毎日多くのお客様はJN0-522問題集について私に質問します、例えばJN0-522問題集の命中率とか、支払いした後どのぐらい問題集をもらえるとか、一回で二つの問題集を買うなら割引できますか？もし新しい資料が出たらまた発送するのかとか、いろいろな問題があって、でもこれらの質問よりもしJN0-522試験で不合格になった場合どうなるのかこういう質問がもっと多いらしい。
わが社のウェブサイトにある科目は全部合格保証いたします、何かの事情で不合格になる場合全額返済します。それに支払いした後20以内で問題集を送ります、もし私達の問題集が更新したら、もう一度送ります、わが社のアフターサービスは絶対お気にいただけると思います
これからJN0-522無料問題集を皆と分かち合います
10.Which statement is correct about tunnel interfaces?
A.They can have overlapping IP addresses.
B.They need to be configured in the zone where the protected resources reside.
C.They can be unnumbered and used in policy-based translations if the interface is in route mode.
D.They can be unnumbered from any interface residing on the same virtual router as the protected
resources.
Answer:D
11.You want to minimize the number of IP addresses, subnets, and policies in use. How should you
configure your tunnel interface?
A.Configure the tunnel interface with an IP address with a 32 bit subnet mask.
B.Configure the tunnel interface with an IP address with a 30 bit subnet mask.
C.Configure the tunnel interface as unnumbered and place the interface in the same zone as the
designated interface.
D.Configure the tunnel interface as unnumbered, but place the tunnel interface in a different zone than the
designated interface.
Answer:C
12.What is the purpose of the "Permitted IP" address on a ScreenOS device?
A.It defines a list of addresses that are trusted to perform management on the ScreenOS device.
B.It is used in policy rules to determine which user traffic is allowed through the ScreenOS device.
C.It defines which range of addresses that can access devices connected to the ScreenOS device.
D.It is the address that an external device uses to gain management access to a ScreenOS device.
Answer:A
14.Which ScreenOS CLI command is required to enable a policy during specified times, days, or dates?
A.set time
B.set clock
C.set calendar
D.set scheduler
Answer:D
15.Which ScreenOS CLI command would be useful for troubleshooting a policy deny?
A.get flow debug
B.debug flow basic
C.exec flow analysis
D.debug session basic
Answer:B
16.Assuming factory default settings, which statement describes the minimum requirements for WebUI
management access to the SSG 5?
A.Connect a PC addressed on the 192.168.1.0 subnet to any interface, open a browser and access
192.168.1.1.
B.Terminate the bootup sequence from the console device, open a browser on the console device and
access 192.168.1.1.
C.Connect a PC addressed on the 192.168.1.0 subnet, to the highest numbered interface and open a
browser and access 192.168.1.1.
D.Using the CLI, define an IP address on a physical interface, connect a PC to the interface and open a
browser to the interface address.
Answer:C
わが社のウェブサイトにある科目は全部合格保証いたします、何かの事情で不合格になる場合全額返済します。それに支払いした後20以内で問題集を送ります、もし私達の問題集が更新したら、もう一度送ります、わが社のアフターサービスは絶対お気にいただけると思います
これからJN0-522無料問題集を皆と分かち合います
10.Which statement is correct about tunnel interfaces?
A.They can have overlapping IP addresses.
B.They need to be configured in the zone where the protected resources reside.
C.They can be unnumbered and used in policy-based translations if the interface is in route mode.
D.They can be unnumbered from any interface residing on the same virtual router as the protected
resources.
Answer:D
11.You want to minimize the number of IP addresses, subnets, and policies in use. How should you
configure your tunnel interface?
A.Configure the tunnel interface with an IP address with a 32 bit subnet mask.
B.Configure the tunnel interface with an IP address with a 30 bit subnet mask.
C.Configure the tunnel interface as unnumbered and place the interface in the same zone as the
designated interface.
D.Configure the tunnel interface as unnumbered, but place the tunnel interface in a different zone than the
designated interface.
Answer:C
12.What is the purpose of the "Permitted IP" address on a ScreenOS device?
A.It defines a list of addresses that are trusted to perform management on the ScreenOS device.
B.It is used in policy rules to determine which user traffic is allowed through the ScreenOS device.
C.It defines which range of addresses that can access devices connected to the ScreenOS device.
D.It is the address that an external device uses to gain management access to a ScreenOS device.
Answer:A
14.Which ScreenOS CLI command is required to enable a policy during specified times, days, or dates?
A.set time
B.set clock
C.set calendar
D.set scheduler
Answer:D
15.Which ScreenOS CLI command would be useful for troubleshooting a policy deny?
A.get flow debug
B.debug flow basic
C.exec flow analysis
D.debug session basic
Answer:B
16.Assuming factory default settings, which statement describes the minimum requirements for WebUI
management access to the SSG 5?
A.Connect a PC addressed on the 192.168.1.0 subnet to any interface, open a browser and access
192.168.1.1.
B.Terminate the bootup sequence from the console device, open a browser on the console device and
access 192.168.1.1.
C.Connect a PC addressed on the 192.168.1.0 subnet, to the highest numbered interface and open a
browser and access 192.168.1.1.
D.Using the CLI, define an IP address on a physical interface, connect a PC to the interface and open a
browser to the interface address.
Answer:C