ジュニパーネットワークス技術認定資格プログラム（JNTCP）で、ジュニパーネットワークスのネットワーク／セキュリティ製品の設定.トラブルシューティングに関する能力を認定します。だからJN0-522
の試験を受けたい人がたくさんいます、でもまだいい学習資料が見つからないことに困っている人も少なくないと思います、今KILLTESTはJN0-522の更新版をリリースしました、このJN0-522問題集
精度が高くて、本当に信用できるよ。何よりこの問題集は合格することを保証して、万が一不合格になる場合全額返済します。詳しいことはhttp://www.killtest.jp/
を見てください
JN0-522の部分問題集、皆さん、参考のため、ご覧ください
10.Which statement is correct about tunnel interfaces?
A.They can have overlapping IP addresses.
B.They need to be configured in the zone where the protected resources reside.
C.They can be unnumbered and used in policy-based translations if the interface is in route mode.
D.They can be unnumbered from any interface residing on the same virtual router as the protected
resources.
Answer:D
11.You want to minimize the number of IP addresses, subnets, and policies in use. How should you
configure your tunnel interface?
A.Configure the tunnel interface with an IP address with a 32 bit subnet mask.
B.Configure the tunnel interface with an IP address with a 30 bit subnet mask.
C.Configure the tunnel interface as unnumbered and place the interface in the same zone as the
designated interface.
D.Configure the tunnel interface as unnumbered, but place the tunnel interface in a different zone than the
designated interface.
Answer:C
12.What is the purpose of the "Permitted IP" address on a ScreenOS device?
A.It defines a list of addresses that are trusted to perform management on the ScreenOS device.
B.It is used in policy rules to determine which user traffic is allowed through the ScreenOS device.
C.It defines which range of addresses that can access devices connected to the ScreenOS device.
D.It is the address that an external device uses to gain management access to a ScreenOS device.
Answer:A
14.Which ScreenOS CLI command is required to enable a policy during specified times, days, or dates?
A.set time
B.set clock
C.set calendar
D.set scheduler
Answer:D
15.Which ScreenOS CLI command would be useful for troubleshooting a policy deny?
A.get flow debug
B.debug flow basic
C.exec flow analysis
D.debug session basic
Answer:B
16.Assuming factory default settings, which statement describes the minimum requirements for WebUI
management access to the SSG 5?
A.Connect a PC addressed on the 192.168.1.0 subnet to any interface, open a browser and access
192.168.1.1.
B.Terminate the bootup sequence from the console device, open a browser on the console device and
access 192.168.1.1.
C.Connect a PC addressed on the 192.168.1.0 subnet, to the highest numbered interface and open a
browser and access 192.168.1.1.
D.Using the CLI, define an IP address on a physical interface, connect a PC to the interface and open a
browser to the interface address.
Answer:C
19.Which command can you use to view the log of IKE negotiations and results?
A.get event type 536
B.get ike cookie
C.get sa active
D.debug ike basic
Answer:A
20.What is the purpose of the VLAN1 interface?
A.It provides policy-based NAT for 802.1Q VLANs.
B.It provides an interface that can be used with 802.1Q VLANs in transparent mode.
C.It provides the ScreenOS device with a routable IP address while operating in route mode.
D.It provides an interface that can be used to remotely manage the ScreenOS device while operating in
transparent mode.
Answer:D
http://www.killtest.jp/JNCIA/
JN0-522の部分問題集、皆さん、参考のため、ご覧ください
10.Which statement is correct about tunnel interfaces?
A.They can have overlapping IP addresses.
B.They need to be configured in the zone where the protected resources reside.
C.They can be unnumbered and used in policy-based translations if the interface is in route mode.
D.They can be unnumbered from any interface residing on the same virtual router as the protected
resources.
Answer:D
11.You want to minimize the number of IP addresses, subnets, and policies in use. How should you
configure your tunnel interface?
A.Configure the tunnel interface with an IP address with a 32 bit subnet mask.
B.Configure the tunnel interface with an IP address with a 30 bit subnet mask.
C.Configure the tunnel interface as unnumbered and place the interface in the same zone as the
designated interface.
D.Configure the tunnel interface as unnumbered, but place the tunnel interface in a different zone than the
designated interface.
Answer:C
12.What is the purpose of the "Permitted IP" address on a ScreenOS device?
A.It defines a list of addresses that are trusted to perform management on the ScreenOS device.
B.It is used in policy rules to determine which user traffic is allowed through the ScreenOS device.
C.It defines which range of addresses that can access devices connected to the ScreenOS device.
D.It is the address that an external device uses to gain management access to a ScreenOS device.
Answer:A
14.Which ScreenOS CLI command is required to enable a policy during specified times, days, or dates?
A.set time
B.set clock
C.set calendar
D.set scheduler
Answer:D
15.Which ScreenOS CLI command would be useful for troubleshooting a policy deny?
A.get flow debug
B.debug flow basic
C.exec flow analysis
D.debug session basic
Answer:B
16.Assuming factory default settings, which statement describes the minimum requirements for WebUI
management access to the SSG 5?
A.Connect a PC addressed on the 192.168.1.0 subnet to any interface, open a browser and access
192.168.1.1.
B.Terminate the bootup sequence from the console device, open a browser on the console device and
access 192.168.1.1.
C.Connect a PC addressed on the 192.168.1.0 subnet, to the highest numbered interface and open a
browser and access 192.168.1.1.
D.Using the CLI, define an IP address on a physical interface, connect a PC to the interface and open a
browser to the interface address.
Answer:C
19.Which command can you use to view the log of IKE negotiations and results?
A.get event type 536
B.get ike cookie
C.get sa active
D.debug ike basic
Answer:A
20.What is the purpose of the VLAN1 interface?
A.It provides policy-based NAT for 802.1Q VLANs.
B.It provides an interface that can be used with 802.1Q VLANs in transparent mode.
C.It provides the ScreenOS device with a routable IP address while operating in route mode.
D.It provides an interface that can be used to remotely manage the ScreenOS device while operating in
transparent mode.
Answer:D
http://www.killtest.jp/JNCIA/