こんにちは、今日皆さんにお勧めしたいのはE20-340問題集です、E20-340試験最近もてるらしい、でもどうやってE20-340認証を手に入れます。努力はもちろんのこと、でも努力だけで、絶対試験を通れますか、今の社会で、一番重要なのは何ですか、一番重要なのはやはり効率である、仕事であろうと勉強であろうと、もし時間と精力を節約できる方法があれば、きっとこの方法で実行します。でもこの方法が本当にあるのか、答えはありますよ。弊社のE20-340問題集を試してみようか、96%の合格率は貴方学習効率を大きくアップします、お使えば、絶対がっかりしない。万が一不合格になった場合、KILLTESTは全額を返済することを保証します、弊社の製品の品質と価値は文句の付けない物と信じてください。私達はあなたのおいでいただことを期待しています。
e20-340の問題集皆と分かち合います
1. What is the maximum number of drives and LUNs supported by a CX3-40?
A. 240 drives and up to 1,024 LUNs
B. 256 drives and up to 1,024 LUNs
C. 480 drives and up to 2,048 LUNs
D. 512 drives and up to 4,096 LUNs
Answer: A
2. Which port is required at installation in order to configure a back-end bus on a CX4?
A. Port 0 A-Bus 0
B. Port 1 B-Bus 1
C. Port 0 A-Bus1
D. Port 3 B-Bus2
Answer: A
3. After the initial CX4 configuration has been set up and persisted, a customer would like to add
additional back-end and front-end ports. In the diagram, which logical port assignments will be given to
port 1 and port 3, respectively?
A. Port 1 - BE1, Port 3 - FE3
B. Port 1 - BE2, Port 3 - FE2
C. Port 1 - FE1, Port 3 - BE2
D. Port 1 - FE3, Port 3 - BE2
Answer: A
4. What is the hard-coded Ethernet IP address for a SP B service port in a CX3-20 and CX3-40?
A. 128.221.1.251
B. 128.122.2.251
C. 128.221.1.250
D. 128.122.2.250
Answer: A
5. Using the Fibre Channel fan-in rule, what is the maximum number of storage systems a host can attach
to?
A. 2
B. 4
C. 8
D. 16
Answer: B
6. Which cable type is required to connect the DAE2P to the DAE3P?
A. HSSDC - HSSDC
B. HSSDC2 - HSSDC2
C. HSSDC - HSSDC2
D. HSSDC - HSSDC3
Answer: B
7. Which port would you use to Telnet directly into the CLARiiON?
A. Comm Port RS-232
B. Management LAN
C. Service LAN
D. SPS Serial Port RS-232
Answer: A
8. According to EMC best practice, what is the proper sequence for powering up a CLARiiON array?
A. Power on SP A and then power on SP B
B. Power on the master switch and then power on each SP
C. Power on the master switch; both SPs will power on automatically
D. Turn on the power switch for each SPS and then power on the master switch
Answer: D
9. What is the first thing you need to know when starting the Initialization Utility?
A. Domain that the array is apart of
B. IP address of Management Port
C. Serial number of the array
D. Version of FLARE on the array
Answer: C