Juniper
ネット会社はその専用のプラットフォームと先進的なソフトウェアを通して、業界が1歩革新を踏み出すことを推進します。Juniperネット会社は研究と開発の安全高性能インテリジェント・ネットワークとソフトウェアの方面で極めて優秀であることを公認されて、しかもずっと業界の中で最も創始精神が富んでいるの会社の1つとして、会社が出した各種の理論はネットと企業のモデルチェンジを推進します。
JN0-201 の問題集みんなと分かち合います
1. Firewall filters can be used to accept, discard, or reject packets based on _____. (Choose three.)
A. protocol type
B. MAC address
C. TCP or UDP port
D. source and destination IP address
Answer: ACD
2. A firewall filter is applied as an input filter on a transit interface. What three types of traffic will this affect?
(Chose three.)
A. inbound traffic transiting the router
B. outbound traffic transiting the router
C. traffic destined to the Routing Engine
D. traffic destined to the interface address on which the filter is applied
Answer: ACD
3. By default, which command can be used to display information about packets that have been logged
with the syslog firewall filter action?
A. show log
B. show firewall
C. show log messages
D. show firewall log
Answer: C
4. During OSPF adjacency formation, in what state is a router when it is negotiating to be in charge of the
database synchronization process?
A. Init
B. 2Way
C. ExStart
D. Exchange
Answer: C
5. Why would you make a non-backbone area a stub or not-so-stubby area?
A. to aggregate routes learned from the ABR
B. to lower the cost of routes advertised by the ABR
C. to connect a non-contiguous area to the backbone
D. to decrease the size of the link-state database in that area
Answer: D
6. What is the purpose of the OSPF link-state update packet?
A. describes a change to the OSPF hello timer
B. carries one or more link-state advertisements
C. establishes and maintains neighbor relationships
D. describes the contents of the entire link-state database
Answer: B
JN0-201 の問題集みんなと分かち合います
1. Firewall filters can be used to accept, discard, or reject packets based on _____. (Choose three.)
A. protocol type
B. MAC address
C. TCP or UDP port
D. source and destination IP address
Answer: ACD
2. A firewall filter is applied as an input filter on a transit interface. What three types of traffic will this affect?
(Chose three.)
A. inbound traffic transiting the router
B. outbound traffic transiting the router
C. traffic destined to the Routing Engine
D. traffic destined to the interface address on which the filter is applied
Answer: ACD
3. By default, which command can be used to display information about packets that have been logged
with the syslog firewall filter action?
A. show log
B. show firewall
C. show log messages
D. show firewall log
Answer: C
4. During OSPF adjacency formation, in what state is a router when it is negotiating to be in charge of the
database synchronization process?
A. Init
B. 2Way
C. ExStart
D. Exchange
Answer: C
5. Why would you make a non-backbone area a stub or not-so-stubby area?
A. to aggregate routes learned from the ABR
B. to lower the cost of routes advertised by the ABR
C. to connect a non-contiguous area to the backbone
D. to decrease the size of the link-state database in that area
Answer: D
6. What is the purpose of the OSPF link-state update packet?
A. describes a change to the OSPF hello timer
B. carries one or more link-state advertisements
C. establishes and maintains neighbor relationships
D. describes the contents of the entire link-state database
Answer: B