JNCIA
試験は受験生にBGP/OSPF/ISIS/について技術の理解をテストして受験料は１２５ドルで、試験時間６０分、６０多くの多肢選択題があります。JNCIS試験は受験生にBGP/IGP/MPLS/IPV6/Multicast/IPv6/CoSについての技術理解をテストして、JNCIAより難しくて受験料は125ドル、試験時間は９０分、75多くの多肢選択題があります
下記はJN0-522 の問題集でございます
1.Your VPN tunnel does not pass traffic. You run the get ike cookie command and discover that there is no
cookie. Which two should be verified? (Choose two.)
A.routes
B.Phase 1 configuration options
C.Phase 2 configuration options
D.selected quick mode encryption algorithms
Answer:A B
2.Which ScreenOS CLI policy statement keyword would enable a policy only during specified times, days,
and/or dates?
A.at
B.calendar
C.schedule
D.scheduler
Answer:C
3.Which ScreenOS CLI command would be used to view traffic logs?
A.get traffic
B.get log policy
C.get policy log
D.get log traffic
Answer:D
5.You enter the following command: set int e0/8 mip 1.1.8.32 host 10.1.10.32 netmask 255.255.255.255
How many MIP address translations have you just configured?
A.1
B.8
C.128
D.256
Answer:A
6.What needs to be configured in Phase 2 of a route-based VPN, that does not need to be configured in a
policy-based VPN?
A.proxy-id
B.tunnel-binding
C.transport mode
D.custom proposals
Answer:B
10.Which statement is correct about tunnel interfaces?
A.They can have overlapping IP addresses.
B.They need to be configured in the zone where the protected resources reside.
C.They can be unnumbered and used in policy-based translations if the interface is in route mode.
D.They can be unnumbered from any interface residing on the same virtual router as the protected
resources.
Answer:D
11.You want to minimize the number of IP addresses, subnets, and policies in use. How should you
configure your tunnel interface?
A.Configure the tunnel interface with an IP address with a 32 bit subnet mask.
B.Configure the tunnel interface with an IP address with a 30 bit subnet mask.
C.Configure the tunnel interface as unnumbered and place the interface in the same zone as the
designated interface.
D.Configure the tunnel interface as unnumbered, but place the tunnel interface in a different zone than the
designated interface.
Answer:C
12.What is the purpose of the "Permitted IP" address on a ScreenOS device?
A.It defines a list of addresses that are trusted to perform management on the ScreenOS device.
B.It is used in policy rules to determine which user traffic is allowed through the ScreenOS device.
C.It defines which range of addresses that can access devices connected to the ScreenOS device.
D.It is the address that an external device uses to gain management access to a ScreenOS device.
Answer:A
下記はJN0-522 の問題集でございます
1.Your VPN tunnel does not pass traffic. You run the get ike cookie command and discover that there is no
cookie. Which two should be verified? (Choose two.)
A.routes
B.Phase 1 configuration options
C.Phase 2 configuration options
D.selected quick mode encryption algorithms
Answer:A B
2.Which ScreenOS CLI policy statement keyword would enable a policy only during specified times, days,
and/or dates?
A.at
B.calendar
C.schedule
D.scheduler
Answer:C
3.Which ScreenOS CLI command would be used to view traffic logs?
A.get traffic
B.get log policy
C.get policy log
D.get log traffic
Answer:D
5.You enter the following command: set int e0/8 mip 1.1.8.32 host 10.1.10.32 netmask 255.255.255.255
How many MIP address translations have you just configured?
A.1
B.8
C.128
D.256
Answer:A
6.What needs to be configured in Phase 2 of a route-based VPN, that does not need to be configured in a
policy-based VPN?
A.proxy-id
B.tunnel-binding
C.transport mode
D.custom proposals
Answer:B
10.Which statement is correct about tunnel interfaces?
A.They can have overlapping IP addresses.
B.They need to be configured in the zone where the protected resources reside.
C.They can be unnumbered and used in policy-based translations if the interface is in route mode.
D.They can be unnumbered from any interface residing on the same virtual router as the protected
resources.
Answer:D
11.You want to minimize the number of IP addresses, subnets, and policies in use. How should you
configure your tunnel interface?
A.Configure the tunnel interface with an IP address with a 32 bit subnet mask.
B.Configure the tunnel interface with an IP address with a 30 bit subnet mask.
C.Configure the tunnel interface as unnumbered and place the interface in the same zone as the
designated interface.
D.Configure the tunnel interface as unnumbered, but place the tunnel interface in a different zone than the
designated interface.
Answer:C
12.What is the purpose of the "Permitted IP" address on a ScreenOS device?
A.It defines a list of addresses that are trusted to perform management on the ScreenOS device.
B.It is used in policy rules to determine which user traffic is allowed through the ScreenOS device.
C.It defines which range of addresses that can access devices connected to the ScreenOS device.
D.It is the address that an external device uses to gain management access to a ScreenOS device.
Answer:A