Pass4Testを選ぶかどうか状況があれば、弊社の無料なサンプルをダウンロードしてから、決めても大丈夫です。こうして、弊社の商品はどのくらいあなたの力になるのはよく分かっています。Pass4TestはJuniper JN0-343認証試験を助けって通じての最良の選択で、１００％のJuniper JN0-343認証試験合格率のはPass4Test最高の保証でございます。君が選んだのはPass4Test、成功を選択したのに等しいです。
JuniperのJN0-343認定試験を一回合格するためには必ず良い準備しなければなりません。完全な知識がこの高度専門の試験に合格するのは必要でPass4Testは君にこれらの資源を完全な需要に備わっています。
Pass4Testは最高な品質で最速なスピードでJuniperのJN0-343認定試験の資料を更新するサイトでございます。もしかすると君はほかのサイトもJuniperのJN0-343認証試験に関する資料があるのを見つけた、比較したらPass4Testが提供したのがいちばん全面的で品質が最高なことがわかりました。
試験番号：JN0-343問題集
試験科目：Juniper 「Juniper Networks Certified Internet Specialist (JNCIS-ENT)」
今は時間がそんなに重要な社会でもっとも少ないお時間を使って試験に合格するのは一番よいだと思います。Pass4Testが短期な訓練を提供し、一回に君の試験に合格させることができます。試験に失敗したら、全額で返金いたします。
Pass4Testは１００％の合格率を保証するだけでなく、1年間の無料なオンラインの更新を提供しております。最新の資源と最新の動態が第一時間にお客様に知らせいたします。何の問題があったらお気軽に聞いてください。
購入前にお試し,私たちの試験の質問と回答のいずれかの無料サンプルをダウンロード：http://pdf.pass4test.jp/JN0-343.pdf
NO.1 What is the correct sequence of OSPF adjacency formation?
A. Down, Init, ExStart, 2way, Loading, Exchange, Full
B. Down, 2way, Init, ExStart, Exchange, Loading, Full
C. Down, Init, 2way, ExStart, Exchange, Loading, Full
D. Down, Init, 2way, Loading, ExStart, Exchange, Full
Answer: C
Juniper JN0-343認定資格 JN0-343練習問題 JN0-343 JN0-343過去問
NO.2 Which statements are true about graceful Routing Engines switchover (GRES)?
A. Configuration on both Routing Engines must be synchronized.
B. The backup Routing Engine cannot be managed through IP address because RPD does not run on
backup the Routing Engine.
C. Different hostnames must be configured on both Routing-Engines.
D. Both Routing-Engines are managed through a single out-of-band-management IP address.
Answer: A
Juniper認定資格 JN0-343 JN0-343認定証
NO.3 Which statement describes the default Junos OS behavior for OSPF?
A. External LSAs are advertised in a stub area.
B. An ABR does not announce a default route into a stub area.
C. Stub area internal routers generate a default route.
D. Only totally stubby areas need a default route.
Answer: B
Juniper認定証 JN0-343 JN0-343 JN0-343認定証
NO.4 Which three statements correctly describe the default BGP advertisement behavior in the Junos OS?
(Choose three.)
A. Routes learned through EBGP are advertised to IBGP peers.
B. Routes learned through EBGP are advertised to other EBGP peers.
C. Routes learned through IBGP are advertised to other IBGP peers.
D. Routes learned through IBGP will be advertised to EBGP peers.
E. Routes learned through an IGP are automatically advertised to EBGP peers.
Answer: A,B,D
Juniper問題集 JN0-343 JN0-343 JN0-343
NO.5 Which configuration correctly sets interface ge-0/0/4 in trunk mode, carrying VLANs v10 and v20?
A. ge-0/0/4 {
unit 0 {
family ethernet-switching {
vlan {
members [ v10 v20 ];
}
} } }
B. ge-0/0/4 {
unit 0 {
family ethernet-switching {
port-mode trunk;
vlan {
members [ v10 v20 ];
}
}
}
}
C. ge-0/0/4 {
vlan-tagging;
unit 0 {
family ethernet-switching {
port-mode trunk;
vlan {
members [ v10 v20 ];
}
}
}
}
D. ge-0/0/4 {
unit 10 {
family ethernet-switching;
}
unit 20 {
family ethernet-switching;
}
}
Answer: B
Juniper JN0-343 JN0-343参考書 JN0-343
NO.6 Which of the following can be used for both security and loop prevention?
A. firewall filters
B. DHCP snooping
C. dynamic ARP inspection D. MAC move limiting
Answer: D
Juniper JN0-343参考書 JN0-343練習問題 JN0-343 JN0-343参考書
NO.7 Which OSPF LSA type is sent by all routers in an area to advertise its connected subnets?
A. router
B. network
C. external
D. summary
Answer: A
Juniper認定資格 JN0-343練習問題 JN0-343認定資格 JN0-343認定証
NO.8 Click the Exhibit button.
Based on the exhibit, in which spanning-tree state would the indicated port be.?
A. listening
B. learning
C. forwarding
D. blocking
Answer: C
Juniper認定証 JN0-343 JN0-343認証試験 JN0-343
NO.9 Which two of the following are functions of the BGP update message? (Choose two.)
A. It withdraws routes that are no longer valid.
B. It notes that an unsupported option is detected from the open message.
C. It transports routing information between BGP peers.
D. It readvertises routes that have already been sent and acknowledged.
Answer: A,C
Juniper認定資格 JN0-343 JN0-343参考書 JN0-343 JN0-343参考書
NO.10 In the following output, what does the asterisk indicate?
A. The interface is configured as a trunk.
B. The interface is configured for spanning-tree protocol.
C. The interface is active.
D. The interface is inactive.
Answer: C
Juniper JN0-343認定資格 JN0-343練習問題 JN0-343
NO.11 When processing inbound Ethernet frames, which firewall filter is evaluated first by an EX Series
switch?
A. port filter
B. VLAN filter
C. trunk filter
D. route filter
Answer: A
Juniper参考書 JN0-343 JN0-343 JN0-343問題集 JN0-343
NO.12 Which routing-instance type allows the sharing of interface routes and the support features used in
source-based routing?
A. virtual-router
B. vrf
C. forwarding
D. multi-instance
Answer: C
Juniper認定資格 JN0-343 JN0-343 JN0-343 JN0-343 JN0-343
NO.13 Configuring bpdu-timeout-action enables which protection mechanism?
A. root protection
B. BPDU protection
C. loop protection
D. RSTP protection
Answer: C
Juniper JN0-343 JN0-343
NO.14 Which BGP attributes are listed in the correct route selection order?
A. local preference, AS path, origin, MED
B. local preference, MED, AS path, origin
C. AS path, local preference, origin, MED
D. MED, origin, local preference, AS path
Answer: A
Juniper問題集 JN0-343認定資格 JN0-343 JN0-343参考書 JN0-343
NO.15 Given the following output, what has been configured for the 192.168.3.0/24 prefix?
A. per-flow load balancing
B. a floating static route
C. per-packet load balancing
D. a qualified next hop
Answer: A
Juniper JN0-343 JN0-343 JN0-343練習問題
NO.16 What are two valid BPDU types? (Choose two.)
A. topology change notification
B. configuration change
C. configuration
D. root bridge
Answer: A,C
Juniper認定資格 JN0-343 JN0-343 JN0-343参考書 JN0-343認証試験 JN0-343認定試験
NO.17 How much overhead does the GRE header add to an IPv4 packet?
A. 24 bytes
B. 32 bytes
C. 48 bytes
D. 64 bytes
Answer: A
Juniper認定証 JN0-343 JN0-343認定資格 JN0-343 JN0-343参考書 JN0-343参考書
NO.18 Which of the following is enabled by default on an EX Series switch?
A. MAC move limiting
B. storm control
C. IP source guard
D. dynamic ARP inspection
Answer: B
Juniper認定資格 JN0-343認証試験 JN0-343
NO.19 Which two OSPF LSA types can be used to advertise routes between areas? (Choose two.)
A. router
B. network
C. external
D. summary
Answer: C,D
Juniper JN0-343問題集 JN0-343認定証 JN0-343
NO.20 Which OSPF area type can contain Type 7 LSAs?
A. backbone
B. not-so-stubby
C. stub
D. totally stubby
Answer: B
Juniper認定資格 JN0-343問題集 JN0-343認定試験
NO.21 What is the minimum configuration necessary to create two VLANs and two operational RVIs?
A. Option A
B. Option B
C. Option C
D. Option D
Answer: B
Juniper練習問題 JN0-343 JN0-343認定試験 JN0-343参考書 JN0-343認定資格
NO.22 Which two pieces of information are communicated by IS-IS TLVs? (Choose two.)
A. network protocols supported
B. designated router priority
C. authentication key
D. PDU Length
Answer: A,C
Juniper認定証 JN0-343認定証 JN0-343認定試験 JN0-343認定試験
NO.23 Which configuration disables a port when more than 30,000 Kbps of broadcast traffic is received over
an aggregated Ethernet interface with two member links?
A. Option A
B. Option B
C. Option C
D. Option D
Answer: C
Juniper認定試験 JN0-343 JN0-343
NO.24 When loop protection is enabled on an interface, what happens when the port stops receiving BPDUs?
A. The port is placed in a loop-inconsistent role.
B. The port is placed into listening mode.
C. The port is transitioned into a forwarding state.
D. The interface is disabled.
Answer: A
Juniper練習問題 JN0-343認定試験 JN0-343 JN0-343
NO.25 Which configuration summarizes external routes in the 172.16.0.0/22 range into a single prefix on an
ABR for Area 1?
A. protocols { ospf { area 0.0.0.1 {
nssa {
default-lsa {
default-metric 1;
metric-type 1;
}
}
area-range 172.16.0.0/22;
}
}
}
B. protocols {
ospf {
area 0.0.0.1 {
nssa {
area-range 172.16.0.0/22;
}
}
}
}
C. protocols {
ospf {
area 0.0.0.1 {
stub summaries;
}
}
}
D. protocols {
ospf {
area 0.0.0.1 {
nssa;
area-range 172.16.0.0/22 restrict;
}
}
}
Answer: B
Juniper JN0-343問題集 JN0-343 JN0-343練習問題
NO.26 Which command correctly assigns AS 65432 as the local router's autonomous system?
A. set protocols bgp local-as 65432
B. set routing-options local-as 65432
C. set protocols bgp autonomous-system 65432
D. set routing-options autonomous-system 65432
Answer: D
Juniper参考書 JN0-343認証試験 JN0-343 JN0-343
NO.27 Which protocol is an IGP?
A. LACP
B. STP
C. OSPF
D. PAGP
Answer: B
Juniper JN0-343過去問 JN0-343認定証 JN0-343認定資格
NO.28 What is the default behavior of a trunk port when it receives transit traffic without a VLAN tag?
A. It drops the traffic.
B. It forwards the traffic.
C. It tags the transit traffic with lowest VLAN ID permitted on the trunk.
D. It tags the transit traffic with highest VLAN ID permitted on the trunk.
Answer: A
Juniper過去問 JN0-343 JN0-343練習問題 JN0-343認証試験
NO.29 Which Junos command correctly configures the ge-0/0/0.0 interface to operate only for IS-IS Level 2?
A. set interfaces ge-0/0/0.0 family iso level 2 enable
B. set interfaces ge-0/0/0.0 family iso level 1 disable
C. set protocols isis interface ge-0/0/0.0 level 2 enable
D. set protocols isis interface ge-0/0/0.0 level 1 disable
Answer: D
Juniper参考書 JN0-343認定証 JN0-343認定試験 JN0-343 JN0-343過去問
NO.30 An administrator finds that traffic from a large file download over an HTTP session is not load-balanced
across multiple links in a LAG. What is the possible cause?
A. Per-packet load-balancing is not configured.
B. The redundant path has a different IGP metric.
C. The hash key is not configured in the forwarding-options stanza.
D. This is the expected behavior.
Answer: D
Juniper JN0-343 JN0-343認定証 JN0-343