■Mode  flow based → packet based

★packet basedで動作確認できていない
 スタティックルート入れてもルーティングテーブルへ反映されない

root> show security flow status
  Flow forwarding mode:
    Inet forwarding mode: flow based
    Inet6 forwarding mode: drop
    MPLS forwarding mode: drop
    ISO forwarding mode: drop
  Flow trace status
    Flow tracing status: off
  Flow session distribution
    Distribution mode: RR-based
  Flow ipsec performance acceleration: off
  Flow packet ordering
    Ordering mode: Hardware

delete security
set security forwarding-options family mpls mode packet-based
set security forwarding-options family iso mode packet-based
set security forwarding-options family inet6 mode packet-based

root> show security flow status
  Flow forwarding mode:
    Inet forwarding mode: packet based
    Inet6 forwarding mode: packet based
    MPLS forwarding mode: packet based
    ISO forwarding mode: packet based
  Flow trace status
    Flow tracing status: off
  Flow session distribution
    Distribution mode: RR-based
  Flow ipsec performance acceleration: off
  Flow packet ordering
    Ordering mode: Hardware

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;


■Interface

ge-0/0/1
ge-0/0/2
ge-0/0/3
ge-0/0/4
ge-0/0/5


◆routed

set interfaces lo0 unit 0 family inet address 192.168.5.5/32
set interfaces fe-0/0/0 unit 0 family inet address 192.168.0.254/24
*seconday上書きされない
 set interfaces fe-0/0/0 unit 0 family inet address 172.16.0.254/24

◆Acccess
set interfaces ge-0/0/3 unit 0 family ethernet-switching port-mode access
set interfaces ge-0/0/3 unit 0 family ethernet-switching vlan members vlan100 

set interfaces ge-0/0/2 unit 0 family ethernet-switching port-mode access
set interfaces ge-0/0/2 unit 0 family ethernet-switching vlan members vlan110


◆Trunk
方法1
set interfaces ge-0/0/5 unit 0 family ethernet-switching port-mode trunk
set interfaces ge-0/0/5 unit 0 family ethernet-switching vlan members vlan100
set interfaces ge-0/0/5 unit 0 family ethernet-switching vlan members vlan110
set interfaces ge-0/0/5 unit 0 family ethernet-switching native-vlan-id vlan120

sh vlan detail 

方法2
set interfaces ge-0/0/0 vlan-tagging
set interfaces ge-0/0/0 unit 0 vlan-id 10
set interfaces ge-0/0/0 unit 0 family inet address 192.168.10.254/24
set interfaces ge-0/0/0 unit 1 vlan-id 20
set interfaces ge-0/0/0 unit 1 family inet address 192.168.20.254/24




◆その他設定

Sppped duplex filter

set interfaces fe-0/0/0 speed 100m
set interfaces fe-0/0/0 link-mode full-duplex
set interfaces fe-0/0/0 fastether-options source-filtering
set interfaces fe-0/0/0 fastether-options source-address-filter 00:00:00:11:22:33

set interfaces ge-0/0/1 ether-options auto-negotiation

※上書き削除

rename interfaces fe-0/0/0 unit 0 family inet address 10.1.1.1/24 to address 10.2.2.2/24
delete interfaces fe-0/0/0 unit 0 family inet address 192.168.0.254/24



★CiscoCatalystと接続時
対向機器がCatalystスイッチで「PVST+」または「rapid-PVST+」が動作している場合、802.1d BPDUは
 VLAN1宛てに送信されるため、Juniper EX側のTrunkポートのNative VLANを1に設定する必要があります。

set interfaces ge-0/0/1 unit 0 family ethernet-switching native-vlan-id 1


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;


◆VLAN

set vlans vlan110 vlan-id 110
set vlans vlan100 filter input TEST

set interfaces irb unit 100 family inet filter output f1

set interface ge-0/0/1 unit 0 family inet filter input from_CENTSV02
set firewall filter TEST  ※ SRX設定不可

set firewall family inet filter TEST term Allow-PC from source-address 10.1.1.1/32
set firewall family inet filter TEST term Allow-PC then accept

set firewall family inet filter TEST term Allow-PING from protocol icmp
set firewall family inet filter TEST term Allow-PING then accept

set firewall family ethernet-switching filter ingress-port-filter term TEST2 from source-address 192.0.2.14

set firewall family ethernet-switching filter ingress-port-filter interface-specific



◆SVI
IRB 可能な時ブリッジ、必要な時ルーティング 拡張L2SoftWareサポート時の名称 ないときはRVI

set interfaces irb unit 110 family inet address 192.0.2.1/25 
set vlans vlan110 vlan-id 110
set vlans vlan110 l3-interface irb.110

RVI(Routed VLAN Interface)は、特定のVLANにルーティング機能を提供する論理L3インターフェース

set interfaces vlan unit 100 family inet address 11.1.1.1/24
set vlans vlan100 vlan-id 100
set vlans vlan100 l3-interface vlan.100


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

■LinkAggregation

●static
 スイッチに設定するLAGの数を定義( 設定例:1つ )
 set chassis aggregated-devices ethernet device-count 1
 LAGの作成( 設定例:L2アクセスポートとして ae0 の作成 )
 set interfaces ae0 unit 0 family ethernet-switching
 LAGに参加させる既存のインターフェースの設定の削除( 設定例:ge-0/0/1とge-0/0/2 )
 delete interfaces ge-0/0/1 unit 0
 delete interfaces ge-0/0/2 unit 0
 LAGに参加させるインターフェースの設定( 設定例:ge-0/0/1とge-0/0/2 )
 set interfaces ge-0/0/2 ether-options 802.3ad ae0
 set interfaces ge-0/0/4 gigether-options 802.3ad ae0
 set interfaces ge-0/0/5 gigether-options 802.3ad ae0
  LAGポートの設定( 設定例:ae0のLAGをアクセスポートとしてVLAN10を割り当て )
 set interfaces ae0 unit 0 family ethernet-switching port-mode access
 set interfaces ae0 unit 0 family ethernet-switching vlan members vlan100

 LAGインターフェースを、全てのVLANトラフィックを転送するL2トランクポートする場合の設定は以下のように設定
  set interfaces ae0 unit 0 family ethernet-switching port-mode trunk vlan members all


●LACP
 LACPとして設定する場合、上記のStatic Link Aggregationの設定に加えて次の設定を追加するだけです。
 LACPの有効化

  set interfaces ae0 aggregated-ether-options lacp active
  set interfaces ae0 aggregated-ether-options lacp periodic fast




;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;


■ACL

●適用
set vlans vlan100 filter input TEST

set interfaces irb unit 110 family inet filter output TEST

set interface ge-0/0/1 unit 0 family inet filter input TEST

vSRX設定不可‘packet`base
 set firewall family ethernet-switching filter ingress-port-filter interface-specific

●フィルタ作成


set firewall filter TEST  ※ SRX設定不可

set firewall family inet filter TEST term Allow-PC from source-address 10.1.1.1/32
set firewall family inet filter TEST term Allow-PC then accept

set firewall family inet filter TEST term Allow-PING from protocol icmp
set firewall family inet filter TEST term Allow-PING then accept

set firewall family ethernet-switching filter ingress-port-filter term TEST from source-address 192.0.2.14


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;


■Routing static


 set routing-options static route 10.1.1.0/24 next-hop 172.16.0.254
 set routing-options static route 10.1.1.0/24 next-hop 172.16.0.254  
 set routing-options static route 0.0.0.0/0 next-hop 172.16.1.254 



■Routing OSPF


 set protocols ospf area 0.0.0.0 interface ge-0/0/0
 set protocols ospf area 0.0.0.0 interface ge-0/0/1

 set protocols ospf area 0.0.0.0 interface ge-0/0/0.0
 set protocols ospf area 0.0.0.0 interface ge-0/0/1.0

 set protocols ospf area 0.0.0.0 interface all
 set protocols ospf area 0.0.0.0 interface ge-0/0/2 disable

passive
 set protocols ospf area 0.0.0.0 interface lo0 passive
 set protocols ospf area 0.0.0.0 interface ge-0/0/1 passive

 show route
show ospf database
show ospf neighbor

●ルータID
 set routing-options router-id 1.1.1.1

●コスト変更
 ① インターフェースのコスト変更 コスト値は 10 加算
 set protocols ospf area 0.0.0.0 interface fe-0/0/1 metric 10

 ② インターフェースの帯域の変更(メトリック上の帯域の変更)
  set interface fe-0/0/1 unit 0 bandwidth 10m

 ③ Reference Bandwidthコマンドによる計算式の変更
  set protocols ospf reference-bandwidth 1G
●priority 変更
 set protocols ospf area 0.0.0.0 interface ge-0/0/0 priority 255
●HelloInterval
 set protocols ospf area 0.0.0.5 interface ge-0/0/0 hello-interval 5


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;


■VR



set routing-instances VR1 instance-type virtual-router
set routing-instances VR2 instance-type virtual-router

set routing-instances VR1 interface ge-0/0/1.0
set routing-instances VR1 interface irb.110

set routing-instances VR1 routing-options instance-import import-from-VR2
set routing-instances VR2 routing-options instance-import import-from-VR1

set policy-options policy-statement import-from-VR1 term 1 from instance VR1
set policy-options policy-statement import-from-VR1 term 1 then accept
set policy-options policy-statement import-from-VR2 term 1 from instance VR2
set policy-options policy-statement import-from-VR2 term 1 then accept

   from route-filter   from prefix-list     from interface


show route instance VR1