إعادة تدوير الأكياس البلاستيكية

وفي مصر، تُستخدم الأكياس البلاستيكية لتخزين المنتجات في المتاجر وأكشاك الطعام في الشوارع. حتى لو قمت بإعادة استخدامها عدة مرات، فسينتهي بك الأمر إلى الكثير من القمامة. حاولت أن أفكر أنه إذا كان من الممكن إعادة تدوير هذه الأكياس البلاستيكية بسهولة، فسيتم إعادة النظر فيها وسيتم الترويج لفرز القمامة.

1. أولاً، ضع علبة فارغة على موقد الغاز وقم بتسخينها.

       

 

2. ضع كيسًا بلاستيكيًا بداخله. هذه المرة وضعت 6 أكياس بلاستيكية شفافة ورقيقة.

      

 

3. بمجرد إضافتها، اضغط عليها في الجزء السفلي من العلبة واقلبها حتى يتم تسخينها بالتساوي.

     

 

4. في النهاية سوف يبدأ في الذوبان، لكن البخار سيخرج، لذا تأكد من التهوية الجيدة وتجنب استنشاق الدخان.

احرص. بمجرد إشعال النار، سوف يهدأ الدخان إلى حد ما. تشتعل فيه النيران تمامًا وتبدأ في الاحتراق

انتظر حتى يذوب. عندما يذوب، أوقفي التسخين وضعي الغطاء لإطفاء النار.

    

 

5. ارتدِ القفازات لتجنب حرق نفسك، وأمسك العلبة بالكماشة، ثم اسكبها في قاع العلبة الفارغة.

    

 

 

 

   

   

 

 

  

 

     

 

6. إذا قمت بعمل نمط في الجزء السفلي من علبة فارغة، يمكنك أيضًا كتابة أحرف قديمة على المادة الصلبة الناتجة.

      

 

 

 

 

   

ملخص

هل درجة انصهار الأكياس البلاستيكية حوالي 130 درجة؟ مع ارتفاع درجة الحرارة، يبدأ في التبخر وينتج الدخان.

في البداية، تم التخلص منها لمنع اشتعال النيران فيها.

واستخدمت المواد الناتجة كدعم للنباتات.

   
 
ومع ذلك، كان غير متساوٍ، وهشًا، ولم يبدو جيدًا، لذلك قررت هذه المرة إشعال النار فيه، وإذابته تمامًا، ثم سكبه في القالب. تبيع المنظمات البيئية آلات إعادة تدوير أغطية زجاجات PET، وما إلى ذلك، ولكن لم تكن هناك آلات إعادة تدوير للأكياس البلاستيكية، لذلك قررت تجربة واحدة. يرجى تعطينا ردود فعل بك.

--------------------------------------------------------------------------------

Plastic bag recycling

In Egypt, plastic bags are used to store products at street shops and food stalls. Even if you reuse it several times, it will end up being a lot of garbage. I tried to think that if these plastic bags could be easily recycled, they would be reconsidered and the sorting of garbage would be promoted.

1. First, place an empty can on the gas stove and heat it up.

       

 

2. Put a plastic bag inside it. This time, I put 6 transparent, thin plastic bags.

      

 

3. Once added, press it against the bottom of the can and turn it over so that it is evenly heated.

     

 

4. Eventually it will start to melt, but steam will come out, so be sure to have good ventilation and avoid breathing in smoke.

Be careful. Once the fire is lit, the smoke will subside somewhat. It completely catches fire and starts to burn

Wait until it melts. When it melts, stop heating and put the lid on to extinguish the fire.

    

 

5. Wear gloves to avoid burning yourself, grab the can with pliers, and pour it into the bottom of the empty can.

    

 

 

   

 

 

      

 

 

    

 

 

   

6. If you make a pattern on the bottom of an empty can, you can also write ancient characters on the resulting solid material.

      

 

 

   

summary

Is the melting point of plastic bags around 130 degrees? As the temperature rises, it begins to vaporize and smoke is produced.

Initially, they were disposed of to prevent it from catching fire.

The resulting materials were used as supports for plants.

   
 
However, it was uneven, fragile, and didn't look good, so this time I decided to light it on fire, melt it completely, and then pour it into the mold. Environmental organizations sell recycling machines for PET bottle caps, etc., but there were no recycling machines for plastic bags, so I decided to try one. Please give us your feedback.

ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー

プラスティク袋のリサイクル

エジプトで、街のお店や屋台のお店で商品を入れてくれるポリ袋。何回か再利用しても、その後、たくさんのゴミになります。このポリ袋が簡単にリサイクルできるなら、見直されて、ゴミの分別も進むのではないかと試みました。

まず、ガクコンロに空き缶を載せて加熱します。

       

 

その中に、ポリ袋を入れていきます。今回は、透明で、薄手のポリ袋6枚入れました。

      

 

入れたら、缶の底に押し付けて、満遍なく加熱されるようにひっくり返したりします。

     

 

やがて、溶け始めますが、蒸気が出てくるので、換気をよくし、煙を吸わないように

注意します。火がつくと、煙は多少おさまります。完全に火がついて燃え始め

溶けるまで待ちます。溶けたら、加熱をやめて、蓋をするなどして火を消します。

 

    

 

火傷をしないように、手袋をして、ペンチなどで缶を掴み、空き缶の底に流し込みます。

    

 

 

   

 

 

      

 

 

        

 

 

 

 

   

空き缶の底に模様をつけたりすると、出来上がりの固形に古代文字などを書くこともできます。

      

 

 

 

   

まとめ

ポリ袋は、融点が130度くらいでしょうか?温度が上がってくると気化し始めて煙が出ます。
当初は、火がつかないように処理していました。
その結果、できたものを、植木の支柱などにしていました。
   
 
しかし、不均一で、壊れやすく見栄えも良くなかったので、今回は、火をつけて、完全に溶かしてから、型に入れる方法を取りました。PETボトルの蓋などは、リサイクルマシンを環境団体などが販売していますが、ポリ袋用のリサイクルマシンは、売っていませんでしたので、試してみました。ご意見をお寄せください。