waves
On the countercultural and radical political front, Jewish hippies Abbie Hoffman and Jerry Rubin, with help from Stew Albert, formed the controversial Youth International Party ("Yippies"), and the four main organizers of the 1969 Woodstock Festival concert were all Jewish, as was Max Yasgur, the man on whose farm the legendary concert took place. In addition, master sound mixer and producer Eddie Kramer was Jewish, as is Bob Dylan.
アアアッ
I am sorry to hear about the noise when turning the GAIN switch in the
original PEQ1 and PAFOUR. Usually when this pops up I get an email and
always reply with the successful fix (see below).
The PEQ1 and PAFOUR used to have Swiss made gold switches from ELMA. Having done the research, these seemed to be the best you can buy.
Since 2007, the newer models PEQ2R and PAFOUR Plus, have been released with a totally new custom made switch by Grayhill which we are very pleased with!
These Grayhills have half the amount (12 instead of 24) of round gold plated contact pads that are located around the circumference of the switch. These are the pads that the gold switch wiper travels over. Having 12 pads instead of 24, they are twice as wide having over 3 x as much contact surface. Also, the gold plating on the new Grayhill switches is the thickest available at the factory. So far in using these for 5 years, these switches ROCK!
But the older Elma switch even with 24 smaller gold pads should work great non the less. We were told by ELMA that if the switches ever get noisy to use De-oxit. We have found that this works excellent but the De-oxit needs to be applied like the procedure below.
1 Remove the top cover.
2 Hold the Unit so that the red knob is towards the floor.
3 Find the access hole at the rear of the large gain switch.
4 Place the clear straw applicator from the Caig De-Oxit into the end of the access hole (the straw is a little too big to fit in the access hole).
5 Press the De-Oxit spray button very slowly so that you trickle about 20 drops of De-oxit into the switch, the switch enclosure is clear plastic and make sure that the switch is visually wet inside.
6 Rotate the Knob back and forth, full travel, about 20-30 times quickly.
The switch should now be noise free. if not repeat steps 2-6.
When I speak to the owners of the older PEQ1, I ask about the switches and they say that they do not have this problem, but every once in a while they do admit that they get pops when changing gain settings.
We thought perhaps the RoHS environmental laws in Europe made plating with gold more difficult. So in the later PEQ1 (about 2006 - 2007) we had Emla make a custom silver plated switch with 10 x the plating thickness and all these units seem to work great. If you older PEQ1's with the gold switch ever wares out, the thick silver replacement switch is a great mod.
The PEQ1 and PAFOUR used to have Swiss made gold switches from ELMA. Having done the research, these seemed to be the best you can buy.
Since 2007, the newer models PEQ2R and PAFOUR Plus, have been released with a totally new custom made switch by Grayhill which we are very pleased with!
These Grayhills have half the amount (12 instead of 24) of round gold plated contact pads that are located around the circumference of the switch. These are the pads that the gold switch wiper travels over. Having 12 pads instead of 24, they are twice as wide having over 3 x as much contact surface. Also, the gold plating on the new Grayhill switches is the thickest available at the factory. So far in using these for 5 years, these switches ROCK!
But the older Elma switch even with 24 smaller gold pads should work great non the less. We were told by ELMA that if the switches ever get noisy to use De-oxit. We have found that this works excellent but the De-oxit needs to be applied like the procedure below.
1 Remove the top cover.
2 Hold the Unit so that the red knob is towards the floor.
3 Find the access hole at the rear of the large gain switch.
4 Place the clear straw applicator from the Caig De-Oxit into the end of the access hole (the straw is a little too big to fit in the access hole).
5 Press the De-Oxit spray button very slowly so that you trickle about 20 drops of De-oxit into the switch, the switch enclosure is clear plastic and make sure that the switch is visually wet inside.
6 Rotate the Knob back and forth, full travel, about 20-30 times quickly.
The switch should now be noise free. if not repeat steps 2-6.
When I speak to the owners of the older PEQ1, I ask about the switches and they say that they do not have this problem, but every once in a while they do admit that they get pops when changing gain settings.
We thought perhaps the RoHS environmental laws in Europe made plating with gold more difficult. So in the later PEQ1 (about 2006 - 2007) we had Emla make a custom silver plated switch with 10 x the plating thickness and all these units seem to work great. If you older PEQ1's with the gold switch ever wares out, the thick silver replacement switch is a great mod.
Digi 192 Bad Output / 13V DC
We have a rather strange problem at the studio. Three of the outputs on
the two 192s have output channels that are bad. When metered they are
outputting over 13 V DC, not the nominal 1.228V AC. It is channel 4 on the 8 out and then channel 5 and 4 on the 16 out unit.
Any suggestions how to fix this? They have been sent back to Digi and they said they were fine. They meter as per above with a DVM and pin the Neve's VU meter. Something is definitely not right. They sound band passed and wrong. The Dsub snakes are fine.
Any suggestions how to fix this? They have been sent back to Digi and they said they were fine. They meter as per above with a DVM and pin the Neve's VU meter. Something is definitely not right. They sound band passed and wrong. The Dsub snakes are fine.
SPモード
IT用語辞典より
輻輳とは：ものが一ヶ所に集中して混雑している状態のこと。IT分野では、電話回線やインターネット回線において利用者のアクセスが特定の宛先に集中することにより、通常行えるはずの通話・通信ができなくなる状況を指す。俗に「回線がパンクする」と表現され、、、
リソース自慢のdocomoさんでもこの有様
日常的に”進捗”とか”輻輳”とか使いまくってるミッションクリティカルな人達はガラケーを
輻輳とは：ものが一ヶ所に集中して混雑している状態のこと。IT分野では、電話回線やインターネット回線において利用者のアクセスが特定の宛先に集中することにより、通常行えるはずの通話・通信ができなくなる状況を指す。俗に「回線がパンクする」と表現され、、、
リソース自慢のdocomoさんでもこの有様
日常的に”進捗”とか”輻輳”とか使いまくってるミッションクリティカルな人達はガラケーを