7. Key switch
Turn on the key switch at “ON” state. The power supply starts to work after about 2 seconds delay. This LED is on
To connect power driver with 0~5V TTL or Analog modulation
3. Output pin port
Operation Instruction for 980nm /2W laser
2.6. TTL modulation are optional. As for the TTL instruction.
Note: The laser only can be operated after the case temperature of the laser system return to the room temperature to avoid the damage of the big temperature range.
1.1. Place the laser head which has the same serial number with the power supply on a stable and better heat-conducting plate, such as metal plate.
2.4. The laser start to work after 2 seconds, the green LED-“Laser” is on. The warming up time is about 15minutes
Front Panel of the power supply：
3. Warranty
1. Product features
3.2.1. Repaired or altered other than in accordance with the terms of this Agreement.
980nm 2W 赤外線 レーザーモジュール 厚ビーム-レーザー砲-レーザー柱-高出力
【規格】Model: T980D2W波長: 980nm出力: ＞1.8W Operating mode: CW横モード構造: Near TE00縦モード構造: Multiスペクトル線幅: 0.15nm偏振方向: Linear vertical偏振比: >50:1ビーム質量: M2<20ビーム発散全角: 5mrad出光穴光斑直径: 3mm×3mm光斑指向安定性: 0.05mradノイズ: <5% 10Hz-50MHzパワー安定性: 5% over 8 hrs rms出光穴高: 25mmレーザー器寸法: L×W×H=100×40×50mmレーザー電源寸法: L×W×H=140×135×80mmケーブル長さ: 0.3m TTL変調効率: 40%-60%TTL変調頻度: 1kHz-30kHzTTL変調方式: 0V-no lasing, 5V-lasing模擬変調: 0-5V模擬変調频率: 1kHz-20kHz製冷方式: TEC定額電圧: 90-260VAC最大消費電力: 10W預熱時間: <5 mintues作動温度: 10℃~35℃保管温度: -20℃~60℃使用寿命: >10,000Hours保証期: 1 year
説明書:
3,2000mWレーザーポインター.2.4. Any other claims not arising directly from material defects in material or workmanship.
Current will rise when rotating the adjustor clockwise
3.1. The warranty is one year from the shipping date.
4.2. Safety with high powered lasers is a critical issue that cannot be overlooked. Despite their brilliant beams and ability to burn, high power laser pointers and portable lasers are only a danger to your eyes. The danger that lasers represent to your eyes though is very serious. The visual receptors in your eyes are part of your central nervous system which means if your eyes are damaged, they do not heal or recover.
2. Current Meter
2. Signal input connector
2. Operation
2.3. Turn on the key switch at “ON” state and the main power of the power supply. The green LED - “Power” is on.
4.1. All lasers and laser light show systems have intrinsic dangers - even laser pointers! Observation of basic laser safety rules and the specific safety regulations of the jurisdiction in which you operate are essential.
2.1. Attach the laser head to the connector of power supply firmly. Please make sure to fasten the locking ring on the connector.
Note: The heat-sink at the top of laser-head is air duct.
4. Laser safety
C. If a cooling fan is needed in the equipment, please make sure the wind direction is the same as right figure.
Analog: for 5V 0~20KHz analogue modulation
To connect power driver with laser head by 9-pin cord
Red LED on when the power driver is auto-shutdown because of over-temperature or some other reasons.
TTL: for 5V 0~30KHz
To connect power driver with 220V or 110V source
2.7. Closing the laser system: switch off the mains power of the power supply and key switch.
B. If the laser system needs to be installed into equipment, please make sure the airflow clear.
It shows the current as factory default
Note: ForTTL function, you need to input5 VDC input voltage.
2.2. Remove the label at aperture.
4. LED for power
4.3.1. Coherent and focused. The energy is focused on a very small area similar to the way a magnifying glass focuses the sun.
1. Power port
6. Power On-Off
4.3. As far as power output, laser pointers and portable lasers do not release that much power. Especially not when compared to a normal 75W or 100W light globe. What makes the light from lasers so dangerous is that it has two unique properties.
2.5. Only for unexpected accident occurs, the red LED-“Error” will be on. That means the laser system works in abnormal state. Please switch off the mains power. Please reset the mains power and key switch after a few minutes, then to restart the laser system again.
4.3.2. Collimated. The light does not spread out from a laser; it stays in a focused narrow beam that makes lasers almost as dangerous at a distance as close up.
5. LED for over-temperature
Green LED on when the driver is normal working
This not to say you should be afraid of lasers or avoid using them. What you should do how ever is to treat lasers with respect, be aware of their dangers and follow some basic guidelines to ensure your safety.
3. LED for normal working
1. Current adjustor
3.2.3. Original identification markings or labels have been removed, defaced or altered.
3.2. This warranty will not apply to those products which have been.
Rear Panel:
3.2.2. Abused, misused, improper handling in use, or storage, or used in an unauthorized or improper manner or without following written procedures supplied by manufacturer.
A. The air duct should not be blocked, and make sure there is nothing placed within 0.05m-0.1m.
